DIMM

  1. Home
  2. Wiki
Two types of DIMMs: a 168-pin SDRAM module (top) and a 184-pin DDR SDRAM module (bottom). The SDRAM module has two notches (rectangular cuts or incisions) on the bottom edge, while the DDR1 SDRAM module has one. Also, each module has eight RAM chips, but the lower one has an unoccupied space for the ninth chip; this space is occupied in ECC DIMMs.
Three SDRAM DIMM slots on a ABIT BP6 computer motherboard.

A DIMM (Dual In-line Memory Module) is a popular type of memory module used in computers. It is a printed circuit board with one or both sides (front and back) holding DRAM chips and pins.[1] The vast majority of DIMMs are manufactured in compliance with JEDEC memory standards, although there are proprietary DIMMs. DIMMs come in a variety of speeds and capacities, and are generally one of two lengths: PC, which are 133.35 mm (5.25 in), and laptop (SO-DIMM), which are about half the length at 67.60 mm (2.66 in).[2]

History

[edit]

DIMMs (Dual In-line Memory Module) were a 1990s upgrade for SIMMs (Single In-line Memory Modules)[3][4] as Intel P5-based Pentium processors began to gain market share. The Pentium had a 64-bit bus width, which would require SIMMs installed in matched pairs in order to populate the data bus. The processor would then access the two SIMMs in parallel.

DIMMs were introduced to eliminate this disadvantage. The contacts on SIMMs on both sides are redundant, while DIMMs have separate electrical contacts on each side of the module.[5] This allowed them to double the SIMMs 32-bit data path into a 64-bit data path.[6]

The name "DIMM" was chosen as an acronym for Dual In-line Memory Module symbolizing the split in the contacts of a SIMM into two independent rows.[6] Many enhancements have occurred to the modules in the intervening years, but the word "DIMM" has remained as one of the generic terms[clarification needed] for a computer memory module.

Form factors

[edit]

Widths

[edit]

DIMMs come in a number of board sizes. In order of descending size: DIMM, SO-DIMM, MiniDIMM, and MicroDIMM.

Regular DIMMs are generally 133.35 mm in length, while SO-DIMMs are generally 67.6 mm in length.[2]

  • 256 MB MicroDIMM PC133 SDRAM (double sided, 4 chips).
    256 MB MicroDIMM PC133 SDRAM (double sided, 4 chips).

SO-DIMM

[edit]
Assorted SO-DIMM Modules
A DDR SO-DIMM slot on a computer motherboard.

A SO-DIMM (pronounced "so dim" /ˈsoʊdɪm/, also spelled SODIMM) or small outline DIMM, is a smaller alternative to a DIMM, being roughly half the physical size of a regular DIMM. The first SO-DIMMs had 72 pins and were introduced by JEDEC in 1997.[7][8][9] Before its introduction, many laptops would use proprietary[10] RAM modules which were expensive and hard to find.[7][11]

SO-DIMMs are often used in computers that have limited space, which include laptops, notebook computers, small-footprint personal computers such as those based on Nano-ITX motherboards, high-end upgradable office printers, and networking hardware such as routers and NAS devices.[12] They are usually available with the same size data path and speed ratings of the regular DIMMs though normally with smaller capacities.

  • The original 72-pin SO-DIMM
    The original 72-pin SO-DIMM
  • SO-DIMM SDR 144pin 128MB ram chip by IBM
    SO-DIMM SDR 144pin 128MB ram chip by IBM
  • A 200-pin PC2-5300 DDR2 SO-DIMM.
    A 200-pin PC2-5300 DDR2 SO-DIMM.
  • A 204-pin PC3-10600 DDR3 SO-DIMM.
    A 204-pin PC3-10600 DDR3 SO-DIMM.

Connector

[edit]
A comparison between 200-pin DDR and DDR2 SDRAM SO-DIMMs, and a 204-pin DDR3 SO-DIMM module. They share the same width but differ in pin and notch placement.[13]
16 GiB DDR4-2666 1.2 V unbuffered DIMM (UDIMM).

Different generations of memory are not interchangable: neither forward compatible nor backward compatible. To make this difference clear and avoid any confusion, their DIMM modules all have different pin counts and/or different notch positions. DDR5 SDRAM is the most recent type of DDR memory and has been in use since 2020.

DIMM
SO-DIMM
  • 72-pin: FPM DRAM and EDO DRAM;[7] different pin configuration from 72-pin SIMM
  • 144-pin: SDR SDRAM,[7] sometimes used for DDR2 SDRAM
  • 200-pin: DDR SDRAM[7] and DDR2 SDRAM
  • 204-pin: DDR3 SDRAM
  • 260-pin: DDR4 SDRAM
  • 260-pin: UniDIMMs carrying either DDR3 or DDR4 SDRAM; differently notched than DDR4 SO-DIMMs
  • 262-pin: DDR5 SDRAM
MiniDIMM
  • 244-pin: DDR2 SDRAM
MicroDIMM
  • 144-pin: SDRAM[7]
  • 172-pin: DDR SDRAM[7]
  • 214-pin: DDR2 SDRAM

Besides pin count there are also physical notches to differentiate the incompatible types of DIMM. For example, the ancient 168-pin SDR SDRAM had different voltage ratings (5.0 V or 3.3 V) and a difference of registered (buffered) vs unbuffered. As a result it has two notch positions to prevent the insertion of the wrong type of module.

  • Notch positions on DDR (top) and DDR2 (bottom) DIMM modules.
    Notch positions on DDR (top) and DDR2 (bottom) DIMM modules.
  • 4 GB DDR VLP DIMM from Kingston Technology
    4 GB DDR VLP DIMM from Kingston Technology

Heights

[edit]

Several form factors are commonly used in DIMMs. Single Data Rate Synchronous DRAM (SDR SDRAM) DIMMs were primarily manufactured in 1.5 inches (38 mm) and 1.7 inches (43 mm) heights, with the nominal value being 30 millimetres (1.2 in). When 1U rackmount servers started becoming popular, these form factor registered DIMMs had to plug into angled DIMM sockets to fit in the 1.75 inches (44 mm) high box. To alleviate this issue, the next standards of DDR DIMMs were created with a "low profile" (LP) height of around 1.2 inches (30 mm). These fit into vertical DIMM sockets for a 1U platform.

With the advent of blade servers, angled slots have once again become common in order to accommodate LP form factor DIMMs in these space-constrained boxes. This led to the development of the Very Low Profile (VLP) form factor DIMM with a height of around 18 millimetres (0.71 in). These will fit vertically in ATCA systems.

Very similar height levels are used for SO-DIMM, Mini-DIMM and Micro-DIMM.[15]

JEDEC standard heights for DIMMs[16]
Generation Full-height (1U) Very low profile (VLP) Notes
Nominal Maximum Nominal Maximum
DDR2[17] 30.00 millimetres (1.181 in) 30.50 millimetres (1.201 in) — —
DDR3[18] 30.00 millimetres (1.181 in) 30.50 millimetres (1.201 in) 18.75 millimetres (0.738 in) 18.90 millimetres (0.744 in)
DDR4[19] 31.25 millimetres (1.230 in) 31.40 millimetres (1.236 in) 18.75 millimetres (0.738 in) 18.90 millimetres (0.744 in)
DDR5[20] 31.25 millimetres (1.230 in) 31.40 millimetres (1.236 in) — —
  • For DIMMs, there is a new height called 2U DIMM at 56.90 millimetres (2.240 in) nominal and 57.05 millimetres (2.246 in) max.
  • DDR5 and LPDDR5 also use CAMM2 units. These are mounted flush to the motherboard.

Notes:

  • Low profile (LP) is not a JEDEC standard.
  • The full JEDEC standards also regulate factors such as thickness.
  • SO-DIMMs for DDR4 and DDR5 maintain the traditional height of 30.00±0.15 mm; see JEDEC MO-310A and MO-337B. The height increase for "full height" DIMM does not apply to SO-DIMM.
  • It is common for higher-end consumer DDR4 DIMMs to exceed the JEDEC full height due to the use of an added heat sink. Some heat sinks add as little as 1 millimetre (0.039 in) while others add up to 5 millimetres (0.20 in).

Similar connectors

[edit]

As of Q2 2017, Asus has had a PCIe based "DIMM.2", which has a similar socket to DDR3 DIMMs and is used to put in a module to connect up to two M.2 NVMe solid-state drives. However, it cannot use common DDR type ram and does not have much support from other than Asus.[21].

Components

[edit]

Organization

[edit]

Most DIMMs are built using "×4" ("by four") or "×8" ("by eight") memory chips with up to nine chips per side; "×4" and "×8" refer to the data width of the DRAM chips in bits. High-capacity DIMMs such as 256 GB DIMMs can have up to 19 chips per side.

In the case of "×4" registered DIMMs, the data width per side is 36 bits; therefore, the memory controller (which requires 72 bits) needs to address both sides at the same time to read or write the data it needs. In this case, the two-sided module is single-ranked. For "×8" registered DIMMs, each side is 72 bits wide, so the memory controller only addresses one side at a time (the two-sided module is dual-ranked).

The above example applies to ECC memory that stores 72 bits instead of the more common 64. There would also be one extra chip per group of eight, which is not counted.

Ranking

[edit]
Main article: Memory rank

Sometimes memory modules are designed with two or more independent sets of DRAM chips connected to the same address and data buses; each such set is called a rank. Ranks that share the same slot, only one rank may be accessed at any given time; it is specified by activating the corresponding rank's chip select (CS) signal. The other ranks on the module are deactivated for the duration of the operation by having their corresponding CS signals deactivated. DIMMs are currently[when?] being commonly manufactured with up to four ranks per module. Consumer DIMM vendors have recently[when?] begun to distinguish between single and dual ranked DIMMs.

After a memory word is fetched, the memory is typically inaccessible for an extended period of time while the sense amplifiers are charged for access of the next cell. By interleaving the memory (e.g. cells 0, 4, 8, etc. are stored together in one rank), sequential memory accesses can be performed more rapidly because sense amplifiers have 3 cycles of idle time for recharging, between accesses.

DIMMs are often referred to as "single-sided" or "double-sided" to describe whether the DRAM chips are located on one or both sides of the module's printed circuit board (PCB). However, these terms may cause confusion, as the physical layout of the chips does not necessarily relate to how they are logically organized or accessed.

JEDEC decided that the terms "dual-sided", "double-sided", or "dual-banked" were not correct when applied to registered DIMMs (RDIMMs).

SPD EEPROM

[edit]

A DIMM's capacity and other operational parameters may be identified with serial presence detect (SPD), an additional chip which contains information about the module type and timing for the memory controller to be configured correctly. The SPD EEPROM connects to the System Management Bus and may also contain thermal sensors (TS-on-DIMM).[22]

Features

[edit]

Speeds

[edit]

For various technologies, there are certain bus and device clock frequencies that are standardized; there is also a decided nomenclature for each of these speeds for each type.

DIMMs based on Single Data Rate (SDR) DRAM have the same bus frequency for data, address and control lines. DIMMs based on Double Data Rate (DDR) DRAM have data but not the strobe at double the rate of the clock; this is achieved by clocking on both the rising and falling edge of the data strobes. Power consumption and voltage gradually became lower with each generation of DDR-based DIMMs.

Another influence is Column Access Strobe (CAS) latency, or CL, which affects memory access speed. This is the delay time between the READ command and the moment data is available. See main article CAS/CL and memory timing.

SDR SDRAM DIMMs
Chip Module Effective clock
(MHz) 		Transfer rate
(MT/s) 		Voltage
(V)
SDR-66 PC-66 66 66 3.3
SDR-100 PC-100 100 100 3.3
SDR-133 PC-133 133 133 3.3
DDR SDRAM (DDR1) DIMMs
Chip Module Memory clock
(MHz) 		I/O bus clock
(MHz) 		Transfer rate
(MT/s) 		Voltage
(V)
DDR-200 PC-1600 100 100 200 2.5
DDR-266 PC-2100 133 133 266 2.5
DDR-333 PC-2700 166 166 333 2.5
DDR-400 PC-3200 200 200 400 2.6
DDR2 SDRAM DIMMs
Chip Module Memory clock
(MHz) 		I/O bus clock
(MHz) 		Transfer rate
(MT/s) 		Voltage
(V)
DDR2-400 PC2-3200 100 200 400 1.8
DDR2-533 PC2-4200 133 266 533 1.8
DDR2-667 PC2-5300 166 333 667 1.8
DDR2-800 PC2-6400 200 400 800 1.8
DDR2-1066 PC2-8500 266 533 1066 1.8
DDR3 SDRAM DIMMs
Chip Module Memory clock
(MHz) 		I/O bus clock
(MHz) 		Transfer rate
(MT/s) 		Voltage
(V)
DDR3-800 PC3-6400 100 400 800 1.5
DDR3-1066 PC3-8500 133 533 1066 1.5
DDR3-1333 PC3-10600 166 667 1333 1.5
DDR3-1600 PC3-12800 200 800 1600 1.5
DDR3-1866 PC3-14900 233 933 1866 1.5
DDR3-2133 PC3-17000 266 1066 2133 1.5
DDR3-2400 PC3-19200 300 1200 2400 1.5
DDR4 SDRAM DIMMs
Chip Module Memory clock
(MHz) 		I/O bus clock
(MHz) 		Transfer rate
(MT/s) 		Voltage
(V)
DDR4-1600 PC4-12800 200 800 1600 1.2
DDR4-1866 PC4-14900 233 933 1866 1.2
DDR4-2133 PC4-17000 266 1066 2133 1.2
DDR4-2400 PC4-19200 300 1200 2400 1.2
DDR4-2666 PC4-21300 333 1333 2666 1.2
DDR4-3200 PC4-25600 400 1600 3200 1.2
DDR5 SDRAM DIMMs
Chip Module Memory clock
(MHz) 		I/O bus clock
(MHz) 		Transfer rate
(MT/s) 		Voltage
(V)
DDR5-4000 PC5-32000 2000 2000 4000 1.1
DDR5-4400 PC5-35200 2200 2200 4400 1.1
DDR5-4800 PC5-38400 2400 2400 4800 1.1
DDR5-5200 PC5-41600 2600 2600 5200 1.1
DDR5-5600 PC5-44800 2800 2800 5600 1.1
DDR5-6000 PC5-48000 3000 3000 6000 1.1
DDR5-6200 PC5-49600 3100 3100 6200 1.1
DDR5-6400 PC5-51200 3200 3200 6400 1.1
DDR5-6800 PC5-54400 3400 3400 6800 1.1
DDR5-7200 PC5-57600 3600 3600 7200 1.1
DDR5-7600 PC5-60800 3800 3800 7600 1.1
DDR5-8000 PC5-64000 4000 4000 8000 1.1
DDR5-8400 PC5-67200 4200 4200 8400 1.1
DDR5-8800 PC5-70400 4400 4400 8800 1.1

Error correction

[edit]

ECC DIMMs are those that have extra data bits which can be used by the system memory controller to detect and correct errors. There are numerous ECC schemes, but perhaps the most common is Single Error Correct, Double Error Detect (SECDED) which uses an extra byte per 64-bit word. ECC modules usually carry a multiple of 9 instead of a multiple of 8 chips as a result.

Register/buffer

[edit]

It is electrically demanding for a memory controller to drive many DIMMs. Registered DIMMs add a hardware register to the clock, address, and command lines so that the signals are refreshed on the DIMM, allowing a reduced load on the memory controller. Variants include LRDIMM with all lines buffered and CUDIMM/CSODIMM with only the clock signal buffered. The register feature often occurs with ECC, but they do not actually depend on each other and can occur independently.

See also

[edit]

References

[edit]
  1. ^ "What is DIMM (Dual Inline Memory Module)?". GeeksforGeeks. 2020-04-15. Archived from the original on 2024-04-07. Retrieved 2024-04-07. In the case of SIMM, the connectors are only present on the single side of the module...DIMM has a row of connectors on both sides(front and back) of the module
  2. ^ a b "Common DIMM Memory Form Factor". 2009-10-06. Archived from the original on 2021-05-13. Retrieved 2021-05-13.
  3. ^ Lyla, Das B. (September 2010). The X86 Microprocessors: Architecture and Programming (8086 to Pentium). Pearson Education India. ISBN 978-81-317-3246-5.
  4. ^ Mueller, Scott (March 7, 2013). Upgrading and Repairing PCs: Upgrading and Repairing_c21. Que Publishing. ISBN 978-0-13-310536-0. Archived from the original on September 17, 2024. Retrieved December 26, 2023 – via Google Books.
  5. ^ Jacob, Bruce; Wang, David; Ng, Spencer (28 July 2010). Memory Systems: Cache, DRAM, Disk. Morgan Kaufmann. ISBN 978-0-08-055384-9.
  6. ^ a b Mueller, Scott (2004). Upgrading and Repairing PCS. Que. ISBN 978-0-7897-2974-3. Archived from the original on 2024-09-17. Retrieved 2023-12-26.
  7. ^ a b c d e f g Mueller, Scott (2004). Upgrading and Repairing Laptops. Que. ISBN 978-0-7897-2800-5. Archived from the original on 2024-09-17. Retrieved 2023-12-26.
  8. ^ "72 Pin DRAM SO-DIMM | JEDEC". Archived from the original on 2024-09-17. Retrieved 2023-11-09.
  9. ^ Fulton, Jennifer (November 9, 2000). "The complete idiot's guide to upgrading and repairing PCs". Indianapolis, IN : Alpha Books – via Internet Archive.
  10. ^ Jones, Mitt (December 25, 1990). "PC Magazine". Ziff-Davis Publishing Company. Archived from the original on September 17, 2024. Retrieved February 4, 2024 – via Google Books.
  11. ^ Norton, Peter; Clark, Scott H. (2002). Peter Norton's New Inside the PC. Sams. ISBN 978-0-672-32289-1.
  12. ^ Synology Inc. "Synology RAM Module". synology.com. Archived from the original on 2016-06-02. Retrieved 2022-03-23.
  13. ^ "Are DDR, DDR2 and DDR3 SO-DIMM memory modules interchangeable?". acer.custhelp.com. Retrieved 2015-06-26.[permanent dead link]
  14. ^ Smith, Ryan (2020-07-14). "DDR5 Memory Specification Released: Setting the Stage for DDR5-6400 And Beyond". AnandTech. Archived from the original on 2021-04-05. Retrieved 2020-07-15.
  15. ^ "CST Inc,DDR5,DDR4,DDR3,DDR2,DDR,Nand,Nor,Flash,MCP,LPDDR,LPDDR2,LPDDR3,LPDDR4,LRDIMM, Memory Tester Automatic DIMM SODIMM Handler Company Provides Memory Solution". www.simmtester.com.
  16. ^ "MICROELECTRONIC OUTLINES (MO)" (PDF). JEDEC.
  17. ^ JEDEC documents MO-256, MO-260, MO-274
  18. ^ JEDEC MO-269J Whitepaper., accessed Aug. 20, 2014.
  19. ^ JEDEC MO-309E Whitepaper., accessed Aug. 20, 2014.
  20. ^ DIMM:MO-329J; SO-DIMM: MO-337B.
  21. ^ ASUS DIMM.2 is a M.2 Riser Card. Archived 2020-06-05 at the Wayback Machine, accessed Jun. 4, 2020.
  22. ^ "Temperature Sensor in DIMM memory modules". Archived from the original on 2016-04-01. Retrieved 2013-03-17.
[edit]
Wikimedia Commons has media related to DIMM.